MASTERTUBE indsprøjtningsslange (rød/gul)

MASTERTUBE indsprøjtningsslange (rød/gul)
Dimension Ø ca. 5/10 mm

artikelnummer 030050

MASTERTUBE Indsprøjtningsslangesystemer

Tætning af betonkonstruktionsfuger stiller høje krav til tætningsteknologien.

MASTERTUBE-injektionsslangen sikrer, at vandrette og lodrette betonkonstruktionsfuger kan forsegles pålideligt og permanent mod vand under og uden tryk. Tilføj til meddelelsesliste

De vigtigste oplysninger på et øjeblik

Tekniske data

artikelnummer:

030050

Artikelgruppe:

300 - Injektionsschlauch

GTIN:

4251689514203

toldtariffens nummer:

39172190

Pakkeenhed:

Rulle

salgsmængde enhed:

100 m

vægt pr.:

Rulle = 10 kg

materiale:

PVC-slange
. Kappe som monofilamentstof

farve:

rot / gelb

Udvendig diameter:

ca. 10 mm

Indvendig diameter:

ca. 5 mm

Udløbsåbninger:

Lys, med ventilfunktion

Anvendelsestemperatur:

depending on injection agent,
approx. + 6°C to +40°C

Testcertifikat/tilladelser:

Generelt testcertifikat fra bygningsmyndigheden (AbP)
MFPA Leipzig
Nr: P-SAC 02 / 5.1 / 21 - 266-1 (PU-harpiks)
Nr: P-SAC 02 / 5.1 / 21 - 266-2 (akrylat)

Tæthed mod vandtryk:

Op til maks. 2 bar (20 m vandsøjle)

Egnede vandskiftezoner:

Svarer til:

Brug klasse A til belastningsklasse 1 og 2 i henhold til WU-retningslinjerne

Emballage:

1 Rolle på 100 m

opbevaring:

Opbevares i ubeskadiget og uåbnet originalemballage på et tørt sted væk fra direkte sollys.

bortskaffelse:

Kan bortskaffes på husholdningsaffaldssteder i overensstemmelse med lokale regler for bortskaffelse af affald

Datablad

Vejledning til installation

The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.

After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.

Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.

The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.

Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.

Fixing on joints with category "rough"

On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.

Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.

All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.

Status: 23.03.2022

Download installationsvejledning

CAD-filer