MASTERTUBE innsprøytningsslange (rød/gul)

MASTERTUBE innsprøytningsslange (rød/gul)
Dimensjon Ø ca. 5/10 mm

artikkelnummer 030050

MASTERTUBE Injeksjonsslangesystemer

Tetting av fuger i betongkonstruksjoner stiller høye krav til tetningsteknologien.

MASTERTUBE-injeksjonsslangen sørger for at horisontale og vertikale betongfuger kan tettes pålitelig og permanent mot vann under og uten trykk. Legg til i varslingslisten

Den viktigste informasjonen på et øyeblikk

Tekniske data

artikkelnummer:

030050

artikkelgruppe:

300 - Injektionsschlauch

GTIN:

4251689514203

tolltariffnummer:

39172190

pakkeenhet:

Rulle

salgsmengde enhet:

100 m

vekt per:

Rulle = 10 kg

materiale:

PVC innerslange
. Kappe som monofilamentstoff

farge:

rot / gelb

Ytre diameter:

ca. 10 mm

Innvendig diameter:

ca. 5 mm

Uttaksåpninger:

Slit, med ventilfunksjon

Påføringstemperatur:

depending on injection agent,
approx. + 6°C to +40°C

Testsertifikat / autorisasjoner:

Generelt testsertifikat fra bygningsmyndighetene (AbP)
MFPA Leipzig
Nr: P-SAC 02 / 5.1 / 21 - 266-1 (PU-harpiks)
Nr: P-SAC 02 / 5.1 / 21 - 266-2 (akrylat)

Tetthet mot vanntrykk:

Opp til maks. 2 bar (20 m vannsøyle)

Egnede soner for vannbytte:

Tilsvarer:

Bruk klasse A for belastningsklasse 1 og 2 i samsvar med WU-retningslinjene

Emballasje:

1 Rolle på 100 m

lagring:

Oppbevares i ubeskadiget og uåpnet originalemballasje på et tørt sted, beskyttet mot direkte sollys

avhending:

Kan kastes på avfallsdeponier for husholdningsavfall i samsvar med lokale forskrifter for avfallshåndtering

Datablad

Installasjonsveiledning

The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.

After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.

Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.

The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.

Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.

Fixing on joints with category "rough"

On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.

Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.

All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.

Status: 23.03.2022

Last ned installasjonsveiledning

CAD-filer